Mech Solutions Ltd 15 PCS 3D Printer Heating Block Cotton and 1 Roll Adhesive Gold Kapton Tape Hotend Nozzle Heat Insulation Cotton for Ultimaker/Makerbot/Creality CR-10S 3D Printer

CA $9.79 In Stock
Customer reviews(6)
+
  • Heat preservation, keep the printer heating evenly and work better
  • You can Punch Holes or Cut fit size to the cotton.
  • Recommend Safe Working Temperature : <300°C
  • Cotton Size: 70mm x 20mm x 2mm Kapton:Width 6mm, Lenght:33m
  • Package including:15PCS x 2mm heating block cotton + 1PCS x 6mm Kapton Tape


Specification
Material: cotton
Cotton Size: 70mm x 0mm x mm
Kapton: Width mm, Lenght:m
Feature: heat preservation

Note: this product only suitable for D printer using indoors

Attention: Small parts, keep away from children

Package including:
15PCS x mm heating block cotton
1PCS xmm Kapton Tape


WARNING!!
1.D printer replacement parts, Always shut off power to the circuit before starting installation work.
.The surface temperature of the D printer might be high, and be careful not to touch the heating element to prevent injury.
.D printer initial operation, Do not run the equipment Unattended state.
.When printing with a PLA(10°C-0°C) or ABS(0°C-50°C)consumable, if the temperature sensor and other accessories fail, it may cause high temperature hazards. Do not run the equipment Unattended state.
5.To ensure the users will use the product safely and properly, Please read your D printer manual first and follow the instructions step by step before using the product.
.Due to the variety of possible end-uses, it is ultimately the responsibility of the customer to determine a product's suitability for a particular application.


Customer reviews(6)

Write Review
Queso del Diablo
April 28, 2018
Great product, arrived a day early and was well packaged. Easy to install, requires some trimming but that you means you can customize the fit to your machine. The extruder nozzle heats up much quicker with this installed.
Stephane Joly
July 29, 2018
item packaged well and very useful. I know that I'll be using this stuff for a long time.
Mark Dennis
July 5, 2018
As described, not much else to say.
Roger Gallant
May 5, 2018
Great ,Delivery was fantastic
R Pilot
November 15, 2018
Difficult to tape because of mounting screws. The tape does not stick well.
Daniel
November 16, 2018
good product very satisfied

Recommend Products

6pcs 20cm Long M3 Diagonal Rod Arm Carbon Push Rod Fisheye Rods high Quality Material Bearing for 3D Printer Push Hilitand

CA $8.81

HICTOP LM8UU Linear Bearings for 3D Printer, RepRap Prusa Mendel DIY CNC Motion, Prusa Mendel, reprap Pack of 6PCs (8mm x 15mm x 24mm) HIC Technology

CA $11.03

Richer-R 5pcs Extruder Nozzle 3D Printer, 5pcs Stainless Steel 3D Printer Extruder Nozzle Cleaning Needle Maintenance Accessory (0.2mm)

CA $6.12

2018 Creality New Designed Upgrade Motherboard Controller Mainboard with Integrated Latest firmware for Creality CR-10S 3D Printer Mech Solutions Ltd

CA $55.99

10pieces 3D Printer Parts Openbuilds 10pcs 5mm Bore Eccentric Spacers for V Wheel Aluminium Extrusion 3D Printer Reprap dropshipping HANDOO

CA $4.83

Mech Solutions Ltd 3D Printer Parts 5 Pcs Brass Extruder Wheel 40 Teeth Drive Gear for CR-10.CR-10S, S4, S5, Ender 3

CA $9.09

10 Pcs 3D Printer V-slots Models Pulley, V-slot POM Plastic Pulley Models, V Groove Ball Bearings Pulley Passive Round Wheels Roller, Black Walfront

CA $12.73

EAONE 10PCS M6 3D Printer Nozzle 0.4mm Brass Extruder Nozzle Print Head for E3D Makerbot

CA $6.99